+86 166 2042 3014 WhatsApp: +86 166 2042 3014 [email protected] Mon–Fri, 09:00–18:00 CST
Get Quote

Optical Switching & Line Protection Units

Optical Switching (ROADM/OXC) and Highly Reliable Line Protection (OLP/Switch) 

OTSLink provides a full product line from basic optical path switching to all-optical WDM scheduling. It covers 1x4/2x2 mechanical optical switches, OLP automatic line protection, and ROADM/OXC optical platforms supporting 9-degree scheduling. With extremely low insertion loss, millisecond-level failover and dynamic spectrum control, your optical transport network stays uninterrupted and highly flexible.

Optical path protection vs. dynamic switching: how to choose by scenario?

 Feature Dimension Optical Path Protection (OLP & Mech Switch) All-Optical Switching (ROADM & OXC)
 Core Function Physical Layer Protection Wavelength Layer Switching
 Working Mechanism Physically switches the optical path channel when the primary or standby fiber is cut Dynamically assigns transmission paths per wavelength, no manual fiber patching required
 Typical Interfaces LC/SC/APC fiber interfaces, passive or actively controlled High-density MPO interfaces with integrated WSS wavelength selective switches
 Applicable Scenarios Trunk cable protection, laboratory automated testing, fiber switching Core DCI interconnects, metro optical network nodes, intra-data-center optical interconnects
 Key Advantages Extreme reliability: millisecond-level switching, service life of over ten million cycles Extreme flexibility: remote configuration, wavelength reconfiguration <3 s, OCM monitoring supported

Key Equipment Selection Points:

  1. Insertion Loss & Channel Isolation:

The physical performance of the optical switch determines the budget of the entire link. Our 1x4 mechanical optical switch features ultra-low insertion loss (typically <0.8dB) and extremely high channel isolation (≥55dB), keeping the optical signal clean even after repeated switching.

  1. Switching Speed & Reliability:

For critical service protection, the switchover must complete before the service can perceive it. Our OLP solution supports <20ms automatic switching; the mechanical optical switch offers a switching life of >10 million cycles and supports latched/latching modes to suit different automated testing needs.

  1. Wavelength Range & Reconfiguration:

ROADM/OXC equipment must support the full C-Band (1528.773-1566.73nm). Our 9-degree ROADM platform supports wavelength reconfiguration in ≤3 s, with an optional OCM (optical channel monitor) module for automated power control.

  1. Operating Mode & Protocol:

Ensure the equipment supports 1+1 unidirectional/bidirectional protection, or matrix switching (M×N) with SNMP/CLI remote control, for seamless integration into your existing NMS.

Eliminate deployment concerns and safeguard the physical and optical layers absolutely

 Customer Concerns OTSLink Solutions
 "Will the optical switch really survive frequent switching?" Guaranteed by measured data: with high-precision automated mass-production processes, our mechanical optical switches pass ten-million-cycle life tests, ensuring faultless operation in laboratory testing and long-term live-network protection.
 "Will packets be lost during automatic switchover when the fiber breaks?" Millisecond-level lossless switching: the OLP solution features extremely low SNR degradation and very fast physical switching, perfectly avoiding the alarm timeout of upper-layer service protocols for truly imperceptible protection.
 "ROADM wavelength configuration is too complex — afraid of misconfiguration?" Dynamic visualized control: our 9-degree ROADM platform supports flexible remote configuration, and with the optional OCM real-time monitoring, the optical power distribution of every wavelength is clear at a glance.
 "Insertion loss is too high and the span cannot reach far enough — what now?" Ultimate optical performance design: we strictly control component tolerances to keep the insertion loss of 1x4 and other optical switches between 0.5dB and 0.8dB, reserving ample link OSNR margin for you.

Typical Application Scenarios and Configuration Recommendations (Use Cases)

Long-haul trunk cable 1+1 protection (Long-haul Fiber Protection)

Recommended configuration: OLP automatic optical line protection unit

Value: Prevents total service outage when a backhoe cuts the cable. If the primary fiber is damaged, automatic switching to the standby fiber completes in milliseconds, keeping services running non-stop.

Intra-data-center and metro WDM nodes (DCI & Metro Nodes)

Recommended configuration: OTS-9D-ROADM optical add/drop multiplexing platform

Value: Compact 1/2-slot form factor with arbitrary C-Band wavelength scheduling. When traffic flows change, no on-site manual patching is needed — the NMS issues one command and reconfiguration completes in 3 seconds.

Laboratory automated testing and optical matrix switching (Lab Automation & Matrix Switching)

Recommended configuration: 2-Channel 2x2 mechanical optical switch

Value: In optical component testing and optical module aging tests, electrical signals control the latching and switching of optical paths, enabling automated test pipelines and greatly improving test efficiency.

Sample Trial & Support

Validate absolute safety at the physical layer (Validate Physical Layer Safety)

Optical switching and protection are the network's last line of defense. OTSLink provides rigorous sample validation support:

Optical specification reports: factory test reports covering insertion loss, crosstalk, return loss and more are provided with every shipment.

Life and switching tests: customers are supported to run stress tests in their own laboratories, verifying the response time and long-term stability of mechanical optical switches.

Customization support: targeted configuration proposals based on your live-network fiber type (single-mode/multi-mode) and interface type (LC/SC/MPO).

All AOC & DAC High-Speed Interconnect Cables DWDM Passive Components High-Speed Optical Transceivers Coherent Transceiver Modules DCI DWDM Chassis Platforms Coherent MXP & Transponder Boards DWDM Inline Monitoring & Auxiliary Modules Optical Switching & Line Protection Units Optical Amplifiers DWDM Fiber Cabling Components
OTS-OXC
OTS-RFA
2-Channel 2x2 Mechanical Optical Switch
1x4 Mechanical Optical Switch
OTS-OADM-DF
OTS-OP
OTS-TDCM
OTS-VOA